| Adapps lango switcher macro |
|---|
...
| Info |
|---|
Getting started with HQV, using an iPad with a LiDAR camera and no additional attachments? You’re in the right place.
This document outlines how to get the best scan results when using HQV 3.0. |
...
Best practices for completing a successful scan
...
|
Best Practices for Completing a Successful Scan
While you’re getting familiar with your new Harvest Quality Vision 3.0 (HQV) scanning system, it’s normal to need
...
a little practice in order to take an effective scan sample.
...
Please pay attention
...
to any on-screen warnings
...
and sounds from the device
...
as they are there to help you take a good scan. Reviewing scan reconstructions on the Croptracker web browser
...
can provide insight into how to achieve the best scanning method as well.
| Info |
|---|
Don’t hesitate to contact support@croptracker.com if you would like your scans reviewed. |
Standard Scan
...
Method
...
Hold your tablet so the camera is facing straight down towards the fruit. The device should be level and parallel to the fruit.
...
The device should be approximately 40cm or 16inches* away from the fruit. If you are too close or too far away from the bin, you cannot start scanning. If your height changes throughout a scan, a warning will appear on the screen. Maintaining a level height is while scanning is important for obtaining accurate information.
| Note |
|---|
* Note: if you are scanning small fruit, you may be instructed to scan closer by default. See note at bottom of page for small fruit scanning tips. |
Cover the top of the bin following an S-shaped motion and return to the same corner you started at as shown in the animation below.
| Widget Connector | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
The green dots will cover areas you have already scanned. You do not need to go over these areas once they have been painted green.
...
Scanning a standard apple bin should take approximately 10-15 seconds.
...
A clicking noise will sound while the camera is actively scanning.
If you move the camera too slow, not enough images will be captured to make a quality scan.
...
If you move the camera too fast, a warning will display on the screen. Moving the camera too fast may result in tracking loss and a decrease in scan accuracy.
| Widget Connector | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
Scan animation
Avoid over-scanning
| Note |
|---|
Continuous movement is important for a thorough scan result. We recommend moving the |
...
device over the bin |
...
so that you have covered over the majority of the fruit within 10-15 seconds. |
| Warning |
|---|
Do not spend time scanning over the same spot repeatedly: it may degrade the overall result, as well as produce larger scan files that take additional processing time. |
Standard Scan Distance
...
If the camera is too far away from the fruit, the dots will not appear in green over the fruit.
If the camera is too close, the scan can lose tracking and focus.
...
An example of how far to hold the iPad above a bin for scanning effectively.
Aim for consistent lighting during your scan
Consistent Lighting
Outdoor and bright, even lighting work best for HQV scanning. Sunlight will produce the best results for size and color. When a scan is taking place outdoors, environmental conditions will vary. This is not an issue if the light remains consistent in the moment you are performing your scan. Take note of your light meter – if there is a notable change in lighting while the scan is active, the tracking process may be negatively impacted.
| Tip |
|---|
Check if there is anything blocking the light meter (like a finger!) or affecting the sensor. |
If you are scanning indoors in a dark area, there is a preference that can be
...
enabled to trigger the
...
device's flashlight to come on when scanning.
...
White balance/color accuracy
| Info |
|---|
See Harvest Quality Vision Preference Menu Options for a detailed guide on accessing and changing HQV preferences. |
In some instances, the color accuracy is impacted negatively if the white balance is
...
changed during a scan. This may be because the iPad has auto-adjusted the white balance to a range based on lighting conditions not reflective of the scanning environment. For example, if the iPad camera was in a dark
...
place, and then
...
you immediately attempt to scan
...
in a brighter
...
place without any pause for auto-adjustment, white balance inaccuracies can occur.
| Tip |
|---|
|
...
|
...
|
...
|
...
|
Scan Resolution for Small Fruit
When scanning fruit smaller than the standard size (apples), the resolution of the images captured in the scan can be adjusted for better results. In the HQV preference menu, there are options for changing the default resolution of the scans. For fruit that is cherry
...
-sized or smaller, the recommended resolution is
...
‘Ultra High’. For fruit the size of a prune plum, the
...
‘High’ resolution setting is recommended.
| Info |
|---|
See Harvest Quality Vision Preference Menu Options for a detailed guide on accessing and changing HQV preferences. |
Check
...
the Scan for Capture Quality
You can assess the quality of your scan’s data capture after you tap the Stop button. Review the scan coverage by moving the camera around the area you just scanned to see that the fruit in the bin is covered fully and that you have not scanned anything
...
that is at a vastly different depth,
...
such as the ground.
You can also check scan quality by looking at the scan reconstruction on the web browser.
| Note |
|---|
If you notice the reconstruction is not level, is missing large chunks |
...
, or looks |
...
strange for any other reason, don’t hesitate to contact support@croptracker.com for review and further training. |
\uD83D\uDCCB Related Articles
| Filter by label (Content by label) | ||||||||
|---|---|---|---|---|---|---|---|---|
|
| Panel | ||||||||
|---|---|---|---|---|---|---|---|---|
| ||||||||
Need a little more support? Not sure you’re using your Croptracker account to the fullest? Get in touch with an expert at support@croptracker.com. You can also book 1-on-1 training with a Croptracker expert at https://www.croptracker.com/1-on-1-training.html. |